6-port PoE switch, 5P+1UP

6-port 10/100 Mbps PoE switch (5xPoE + 1xUplink), electronic fuses, Long Range mode, built-in module, power supply not included.

Key features and functions:

• provides power supply for 5 PoE 802.3af/at or PASSIVE receivers
• allows data transmission up to 280 m (Long Range mode)
• electronic fuse for each PoE channel (auto-reset)
• PoE can be disabled on selected ports
• clear LED indication of power and data transmission status
• wide input voltage range (10–56 VDC)
• output voltage = input voltage
• up to 70 W on the LAN_5 PoE IN/OUT port
• up to 40 W on the other PoE ports
• powered via terminal block (Vin) or from another PASSIVE PoE switch (PoE IN/OUT port)
• cascade power option – one xPoE module powers another through the PoE IN/OUT port
• quick and easy setup with no configuration required
• low power consumption (<1.5W)
• compact size

xPoE-6-11-OF is designed as a universal PoE network switch for IP CCTV systems. Electronic PoE output protection ensures continuous operation of the entire system in the event of a short circuit or overload on a single PoE port, and automatic voltage restoration after the failure has been resolved.

Unmanaged PoE switches and extenders are designed to work with IP cameras and other network devices powered by PoE 802.3af/at and PoE PASSIVE standards.

The “Long Range” mode allows you to increase the transmission range up to 280m using standard UTP twisted pair cable. The switch allows you to work in two modes: standard and extended range. When the Long Range switch is in the OFF position, all ports operate at 100 Mbps and offer Ethernet range up to 100 meters. When the dip switch is set to ON, the range on ports 1 to 4 is increased to 280 meters, while the speed on these ports is reduced to 10 Mbps. This bandwidth is sufficient for the efficient operation of a single camera. In both modes, the speed of UpLink ports 5 and 6 is 100 Mbps. With LongRange mode enabled, we provide greater flexibility in camera placement. Increasing the distance from the switch allows for easier coverage of a large area without the need to build additional distribution points.

“STANDARD” mode (MODE = OFF)

LAN 1 ... LAN 4 - 10/100 Mbps PoE OUT, range up to 100m

LAN 5 - 10/100 Mbps, PoE IN/OUT range up to 100m

LAN 6 - 10/100 Mbps, range up to 100m

“LONG RANGE” mode (MODE = ON)

LAN 1 ... LAN 4 - 10 Mbps PoE OUT, range up to 280m

LAN 5 - 10/100 Mbps, PoE IN/OUT range up to 100m

LAN 6 - 10/100 Mbps, range up to 100m

Regardless of the selected operating mode, the switch supports PoE short-circuit and surge protection to protect network devices.

Port 6 UpLink cannot enable PoE regardless of the selected operating mode. It allows for secure connection of different LAN segments.

Notes:

• by default, LongRange mode is disabled
• changing modes requires a power restart
• it is recommended to test the functionality before deployment
• no VLAN port isolation – all switch ports can communicate with each other uninterrupted, regardless of the operating mode
• for long-distance setups, we recommend powering the switch with 55 V from a dedicated APS-90-550-OF power supply or using an ASUC-100-550-OF converter in buffered sets
• the transmission distance depends on the cable used; Cat5e or Cat6 cables are recommended. Using low-quality cables or CCA cables will significantly reduce the range and limit the voltage available to the camera

The OF (Open Frame) design allows the device to be installed in any enclosure, although the most convenient method is to use dedicated ABOX series enclosures and mounting plates with a special 10.8 mm hole pattern. The spacing matches the mounting holes of the built-in modules. This system allows vertical or horizontal installation of selected devices in any perforated section of the enclosure or mounting plate.

Examples of applications

 

Basic application of xPoE-6-11-OF. 

 

 

Example of using xPoE-6-11-OF powered by another PASSIVE PoE switch.

 

 

 

Example of using xPoE-6-11-OF in a cascade connection.

 

 

 

  

If any part of the diagram appears blurry, right-click the image and open it in a new window — this will allow you to download and view it in full resolution.